Penerbit: Fakultas Teknik, Unila
P-ISSN: 2087-1880
E-ISSN: 2460-1888
DOI: https://doi.org/10.2960/mech
Fakultas Teknik Teknik (semua kategori) Arsitektur
Artikel (198)
Effect of Cutting Parameter Variation on Drilling of AISI 1045: Experimental and Simulation
Burhanuddin, Yanuar
This work is focused on the study of the effect of spindle speed and feed rate on the tool temperature distribution in the drilling of AISI-1045 steel. The e data were collected under different cutting conditions. The maximum tool temperature is predicted during the drilling using finite element sim...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Studi Kekuatan Sambungan Las Baja AISI 1045 dengan Berbagai Metode Posisi Pengelasan
., Tarkono
Lingkup penggunaan teknik pengelasan dalam kontruksi sangat luas, meliputi perkapalan, jembatan, rangka baja, bejana tekan, pipa pesat, pipa saluran, kendaraan rel dan lain sebagainya. Selain untuk pembuatan, proses pengelasan juga digunakan untuk reparasi atau perbaikan. Posisi atau sikap pengelasa...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Analisis Limit Momen Pipa Elbow dengan Beban In-Plane Bending
Lubis, Asnawi
Pipe bends or elbows are of important component in a piping system. In addition to its function for changing the direction of piping due to layout restriction, an elbow can accommodate expansion because it is more flexible than an equivalent straight pipe with the same material and dimension. Howeve...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Reduksi Bising Motor Diesel Menggunakan Partial Enclosure
Suudi, Ahmad
Noise is one of the environmental problems that we must concern on it, not just it can produce  healthy problems, but it can reduce working productivity too. This research is  aimed to reduce noise produced by diesel engine in the laboratory of motor combustion engine.The experiment was conducted ...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Pengaruh Sudut Kontak Statis terhadap Penyebaran Droplet di Atas Permukaan Padat yang Dipanaskan pada Bilangan Weber Menengah
Susila, M. Dyan
The influence of static contact angle on the spreading of droplet on a heated solid surface has been studied experimentally. Static contact angle was important parameter which influenced the impact behavior and heat transfer during the interaction of droplet and solid surface. Droplet substance was ...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Review Dan Analisa Karakteristik Dan Penyebab Kerusakan Sudu Turbin Gas
Risano, Yudi Eka
The present study concerns the review and the analysis of malfunctions characteristic and the reasons of moving blade damage. Such malfunctions are breakage of moving blade in excessive temperature conditions, increasing vibration, little cyclic weariness from frequent heat exchange at start-up and ...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
Investigasi Sifat Mekanik Material Komposit Yang Terbuat Dari Pemanfaatan Limbah Batubara Dengan Matrik Resin Poliester Tak Jenuh
., Zulhanif
Limbah batubara yang dihasilkan oleh sisa pembakaran di industri yang menggunakan boiler belum termanfaatkan secara maksimal untuk menjadi bahan yang lebih bernilai ekonomi, Pada saat ini ada beberapa industri semen yang memanfaatkan hasil lebih batubara sebagai campuran semen yang dikenal dengan is...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010
STUDI EKSPERIMENTAL TENTANG PENGARUH VARIASI RAPAT ARUS PADA HARD CHROME ELECTROPLATING TERHADAP KARAKTERISTIK PERMUKAAN BAJA KARBON RENDAH
Supriadi, Harnowo
The objective of the research is to investigate the effect of  hard chrome electroplating on low carbon steel surface characteristic. This experimental research used low carbon steel as  material  that has been coated by hard chrome electroplating,  chromium powder, and Pb alloy as cathode.  Th...
MECHANICAL; Vol. 1 No. 1 (2010) | 2010