Artikel Terbaru
Telusuri koleksi artikel yang paling baru dipublikasikan.
Total ditemukan 17260 artikel.
Effect of Cutting Parameter Variation on Drilling of AISI 1045: Experimental and Simulation
Oleh: Burhanuddin, Yanuar
This work is focused on the study of the effect of spindle speed and feed rate on the tool temperature distribution in the drilling of AISI-1045 steel. The e data were collected under different cutting conditions. The maximum tool temperature is predicted during the drilling using finite element sim...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
Studi Reduksi Beban Termal ke Dalam Ruangan Secara Konveksi dengan Sistem Underground Thermal Storage Sebagai Altenatif untuk Mendinginkan Ruangan Rumah Hunian
Oleh: Gandidi, Indra Mamad
Space cooling is required all year around in the tropics area especially Indonesia. To provide the space cooling requirement, the electricity cost and environment impact are important aspect that it must be considered. The household in the tropical area is real conditions require a cooling devic...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
Analisis Uji Destructive Dan Non Destructive Terhadap Hasil Sambungan Las V-Tunggal Baja AISI 1045
Oleh: ., Nafrizal
This paper reports the result of study on the strength behaviour of welded joint both destructive and nondestructive testing. The parent metal choosen for the testing was AISI 1045 steel with main parameters of single-V welded form and horizontal welding position. The electrodes used for each parame...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
Studi Perilaku Kegagalan Sambungan Las Tipe TConjunctions Pada Baja Karbon Rendah Dengan Pendekatan Experimen dan Numerik
Oleh: Badaruddin, Mohammad
This research is conducted to investigate failure behavior of welding structure in T-conjunctions type. Welding joint failures were analyzed by both experimental and finite element analysis (2D) approach in terms of stress intensity factor mode I (KI). The stress at the welding zone was strongly inf...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
Analisis Prestasi Lampu Petromax Berbahan Bakar LPG
Oleh: Burhanuddin, Harmen
In order to decrease subsidy cost of kerosene consumption, Indonesian government right now proposes to convert kerosene to LPG. Consequently, the price of kerosene is expensive in society. LPG can be alternatively used as fuel for the petromax lamp. The use of LPG for the petromax lamp fuel is stron...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
Pengaruh Posisi Terhadap Kekuatan Baut dan Gaya Geser Ditinjau dari Morfologi Fracture Surface pada Sambungan Plat
Oleh: Handra, Nofriady
Bolt extension as link which do not destroy connective by component at process unload tide used many in so many industrial area like at bridge construction, building construction and various appliance of engine tool. Usage of amount 3 (bolt fruit three) at 5 (standard hole five) at one particular ex...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 06 September 2011
KEMAMPUAN BENTONIT PELET TEKAN TERAKTIVASI FISIK SEBAGAI PENGGANTI ZEOLIT DALAM MENGHEMAT KONSUMSI BAHAN BAKAR MOTOR DIESEL 4-LANGKAH
Oleh: Wardono, Herry
Propinsi Lampung merupakan salah satu produsen zeolit terbaik dan terbesar di Indonesia. Herry Wardono telah membuktikan kemampuan zeolit Lampung dalam meningkatkan prestasi motor bakar. Disamping zeolit, potensi bahan tambang bentonit juga tersedia melimpah di Propinsi Lampung. Bentonit memiliki ...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 04 April 2011
PEMBUATAN PROGRAM PERANCANGAN TURBIN SAVONIUS TIPE-U UNTUK PEMBANGKIT LISTRIK TENAGA ANGIN
Oleh: Tanti, Novri
The Savonius Wind Turbine is a drag type vertical axis wind turbine, and it operates by cupping and dragging the wind, causing the rotor to turn and generate electricity. The Savonius Wind Turbine usually has about two or three scoops or cups to catch the wind. The design allows the turbine to rotat...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 04 March 2011
FLUKTUASI GAYA PADA PIPA SAMBUNGAN T AKIBAT ALIRAN DUA FASA CAIR-GAS
Oleh: Irsyad, Muhammad
Aliran dua fasa memiliki ketidakstabilan karena pada satu saluran terdapat dua fasa yang berbeda, yang mengakibatkan gaya yang ditimbulkan setiap fasa berbeda-beda. Ketidakstabilan aliran dua fasa dapat mengakibatkan masalah keamanan pada komponen-komponen power, heat transfer, boiler, evaporator, r...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 04 March 2011
KARAKTERISTIK ALAT PENGERING PADI SKALA LAB DENGAN MENGGUNAKAN BAHAN BAKAR SEKAM PADI
Oleh: Ridhuan, Kms.
The drying process is a stage that is quiteimportant to determine the quality of rice is good, especially the rainy season, so the use ofpaddy dryers (oven) is a must. For the heatsource used fuel waste rice husk obtained fromthe rest of the rice mill. Well as efforts toove...
Penerbit: Jurusan Teknik Mesin, Fakultas Teknik, Universitas Lampung • Publikasi: 04 March 2011